Press the transmitter button once more to test the system and start your door moving. Press and hold down the square button on the motor head until the round blue LED light come on, then release the square button.
The long purple LED button will start to blink. Note: if the blue light stays on, go to instructions for Intellicode III, below While the long LED is blinking, hold the remote 4 or 5 feet away and press 3, 4 or 5 times, until the door activates.
Your remote is now programmed. Press the square button once more until the long purple LED comes on and release. The purple LED should be blinking. To unlock the programming feature use a remote that already operates the unit and press it once. Purple light goes solid. Hold the new remote 4 or 5 feet away and press 3, 4 or 5 times until the door activates.
The remote is then programmed Clearing Memory for Remotes and Keypad if present Follow steps 1 and 2 above or step 1 if between and July 8, This clears the receiver memory.
All previously programmed remotes will no longer work with your door. To re-program each remote follow steps 1 through 3 of the programing instructions relative to your opener above.
Programming Digital Remote Transmitters with Internal Set Switches These transmitters work by matching the settings on the internal code setting switches with the same set of switches in the receiver on the garage ceiling. To program a button for one of your doors, follow the instructions below: First, match the settings on the Internal Code Setting Switches with the same set of switches in the receiver on the garage ceiling, as described in the previous programming instructions.
Follow the same procedure for each additional door you wish to program. Installation of Genie GIC Intellicode Receiver Terminals labeled 1, 2 and 3 on the Receiver are connected to their corresponding terminals on the garage door opener Power Head labeled 1, 2 and 3. The smart indicator light will glow steadily for 30 seconds. The LM and LM remotes have a corresponding amber or red, square, learn button. The LM and LM have a corresponding purple, square, learn button. Learn buttons are located on the motor head near the terminal strip for wire connections.
Within 30 seconds, press and hold the button on the hand-held remote. It has learned the code. If light bulbs are not installed, two clicks will be heard. Press and release the remote control button you wish to use the number of times corresponding to the garage door opener type with a Learn button described below: To exit programming, press and release any remote control button except the button that was just programmed.
Enter the pairing code. Press OK when prompted. Method 3. Find the code for your TV. Click your Genie remote's model number. Click the TV option. Select your TV's manufacturer e. Review the five-digit code. Release the buttons when your remote's lights blink.
Again, you'll do this until you see the lights flash twice. Release the buttons when the remote's lights flash. Enter your TV's code. The rest of the setup should occur automatically. The TV and other devices are controlled by it with IR.
IR does both, but for different devices. Not Helpful 26 Helpful I programmed the remote to control my audio receiver, but it only controls the volume. How do I also program the remote to power it on and off? Only the volume can be controlled. I can't speak to the capabilities of other DirecTV remotes. Not Helpful 24 Helpful What more can I do?
Check to see if the receiver is on and then no results change your input settings. Hold the input button and will bring up your TV's input list. Go through each input tv, hdmi 1, hdmi2, etc. Not Helpful 11 Helpful WikiHow's article on repairing a remote control may be of help. Not Helpful 10 Helpful Do any of the other buttons work?
If not, it is likely the batteries are dead. Replace the batteries and try again. Not Helpful 6 Helpful 9. Not Helpful 8 Helpful 4. See if everything is plugged in or check to see what the setup is. Also check to see if you're on the right source. Not Helpful 18 Helpful 8. Hit the Enter or Input button. It will open the source menu. Use the up and down arrows to select the input you want.
Not Helpful 5 Helpful 3. If you press the record button twice, it will record the whole series; if you press it a third time, it will pop up with "Continue Recording", "Change Recording Options", "Cancel This Episode" and "Cancel Entire Series". You will want to click the latter. It will ask, "Do you want to keep the partial recording? Not Helpful 0 Helpful 1.
Change the batteries. The cover is on the back of the remote. It uses 2 AA batteries. If that doesn't help, contact DirecTV, as you probably need them to send you a new remote. Not Helpful 0 Helpful 0. Include your email address to get a message when this question is answered.
Common Genie remote problems stem from low or non-existent battery life. Try replacing the batteries in your remote if you're having difficulties programming or using the remote. Helpful 0 Not Helpful 0. Your Genie remote's lights will blink slowly or fail to light up when the battery life is low.
If your Genie remote won't pair with your Genie receiver, you can hard-reset the receiver by holding down the red "reset" button on the back of the receiver. Helpful 0 Not Helpful 1. Resetting your DIRECTV receiver will return it to factory settings, meaning that you'll have to go back and restore any settings or preferences which you had previously changed.
Helpful 3 Not Helpful 2. Helpful 2 Not Helpful 1. You Might Also Like How to. How to. About This Article. Written by:. Co-authors: 5. Updated: August 10, Article Summary X 1. Thanks to all authors for creating a page that has been read 1,, times.
Steps were perfect and the process helped me learn a wee bit about the settings of DirecTV. I used the model number, and it paired instantly. More reader stories Hide reader stories. Is this article up to date?
Cookies make wikiHow better. By continuing to use our site, you agree to our cookie policy. Mike Cary Aug 18, Fox Apr 14, You just can't beat showing. Rated this article:. Angie Villarreal Dec 15, Great instructions with pictures on programming DirecTV Genie remote. With other instructions, had been using the wrong button.
0コメント